Engineered Wood Flooring Installation

So You’re Ready to Install Your New Flooring…

Anthology Woods is happy to assist you with installing your beautiful new engineered wood flooring. We take great pride in our wood products and work hard to provide you with the highest quality wood floor available. Taking care during installation and continued maintenance will preserve your floor for generations to come.

Engineered wood flooring is a great choice for any installation, but truly excels in environments that are not well-suited for solid wood flooring, such as below grade or over concrete or radiant heat subfloors. Anthology Woods engineered wood floors are designed to be more dimensionally stable than solid wood floors, and therefore more appropriate for these installation environments.

Detailed instructions for preparation of the subfloor and specific installation techniques for these installation methods can be obtained from the National Wood Flooring Association (NWFA) or by using the links provided in this Technical Resources section of our website.

This web page will provide general installation guidelines. Anthology Woods recommends that engineered flooring be installed by an experienced, licensed and bonded flooring contractor. We also recommend following the detailed instructions of the National Wood Flooring Association. Anthology Woods provides the general installation guidelines presented here as a recommendation only. We do not assume responsibility for the installation or finishing of your flooring.

Upon delivery of your floor, inspect the order for any damage that may have incurred during shipment. Make note of any visible damage on the Bill of Lading prior to accepting the shipment. Contact Anthology Woods immediately if there is any damage and we will work with you to file a claim with the shipping company.

Once your wood is delivered, move it immediately into a controlled environment. Do not leave wood products outdoors, in a garage or other outbuilding, or anywhere without temperature and humidity control.

Wood is a natural material that “adapts” to its environment by absorbing or releasing moisture to come into balance with its surroundings. Therefore it is important to acclimate your wood flooring to the environment where it will be installed prior to installation.

Engineered wood flooring should only be placed in the installation area after all wet work is done (this includes drywall, plaster, tile, and painting. The HVAC system should be operational and the environment should be maintained at the same temperature and humidity levels as normal living conditions (generally 60-80 degrees and 30-50% humidity).

Anthology Woods Engineered Wood Flooring does not require the same acclimation procedure as solid wood floors do. It is however, critical that the environment the flooring is being installed in is properly prepared and the above criteria are met regarding temperature and humidity. Store the Engineered Wood Flooring in UNOPENED boxes onsite for 48-72 hours before installation to allow flooring to adjust to room temperature. Do not store the boxes of flooring directly on concrete or close to an exterior wall. Only open as many boxes as can be installed during the course of any installation period.

Anthology Woods floors can be installed over a variety of substrates and specific detailed instructions for different installation methods can be obtained from the National Wood Flooring Association. Generally solid wood flooring is best suited for above grade installations over concrete subfloor (see NWFA guidelines for installations over concrete subflooring or contact Anthology Woods for guidance), with a ventilated crawl space and proper moisture barriers.

Typical wood flooring installation methods are appropriate for Anthology Woods Engineered Wood Flooring. Use an appropriate fastener (1-1/2” to 2” in length) and blind nail through the tongue every 6-8”. Wide plank floors (over 5” face width) are susceptible to increased movement, therefore in addition to blind nailing, apply an appropriate adhesive following the adhesive manufacturers instructions. Additional installation methods, including installation over other subfloor materials can be obtained from the NWFA or by consulting your flooring installer.

If you have ordered a mixed-width product from Anthology Woods, check your Materials Quote and packing list to determine the quantity of each width provided. Many of our mixed width products are sold with roughly equal amounts of each width by square footage, howeversome are not and it is best to double check your packing list for the final tally. There is no set pattern for installing these floors and the particular pattern you choose is up to you and theinstaller. Regardless, it is always best to “rack-out” a large area of the floor prior to installation. This will help in both managing the material to make sure you have enough to complete each run, and with balancing the character, color and aesthetic proportions of your floor.

Most Anthology Woods Engineered Wood Floors are pre-finished. However if you have purchased an un-finished Engineered Wood Floor filling, sanding and finishing should be done by an experienced professional, and should involve sanding through progressively finer grits to remove scuffs and scratches. A variety of different finish types are suitable for Anthology Woods floors and you can learn more about different finishes by visiting our website (www.anthologywoods.com). If you have purchased a natural patina or distressed floor you may wish to simply screen your floor to preserve the patina and character. A screen sand will help soften any over-wood issues and other inconsistencies. Finishing your floor should happen towards the very end of your project when other trades have completed their work and adequate time and space is given for the finish to cure.

If you have additional questions regarding installation please contact Anthology Woods and speak to one of our technical experts. We’re always happy to help!

InstallationAnthology Woods